Injection Device
Syringes can also call Disposable Medical Supplies, Disposable Syringe With Needle and Plastic Needle Tube such as some scientific instruments in chromatography to inject through the rubber septum. Injecting gas into a blood vessel will cause an air embolism. The way to remove air from the syringe to avoid embolism is to turn the syringe upside down, tap it lightly, and squeeze out a little bit of fluid before injecting into the bloodstream.
In some cases where accuracy is not the primary concern of germs, such as quantitative chemical analysis, glass syringes are still used due to the small error of the glass syringe and the smooth movement of the push rod.
You can also inject some of the juices into meat with a syringe to improve taste and texture while cooking, or into pastries when baking. Syringes can also fill ink cartridges with ink.
Injection Device,Intravenous Infusion Set,Iv Infusion Sets,Blood Pressure Monitor Haloxylon Ammodendron Medical Equipment Co., Ltd. , https://www.haloxylonmedical.com
Operating procedure of pharmaceutical packaging machine
1. The green indicator light is on, the upper and lower heat switches are respectively set to the "ON" position, the work table*, the temperature controller controls the forming temperature, and the preset temperature is preset 90C? and 100C?, the second temperature control Heat sealing, temperature preset 120C?-140C? Up and down, forming and heat sealing temperature controller preset temperature, as appropriate.
2, put down the pressure block on the feeding roller, the temperature of the forming heating plate is in place, and then open the main machine, the plastic PVC is first formed, the forming blister is in conformity with the hole position of the heat sealing mold, pay attention to the heat sealing mold seat and put down the heat sealing mold to press the aluminum foil , aluminum foil will drive to the punching. Observe whether the plastic (referred to as the machine surface has been formed PVC) travels left and right offset. If there is a bias, the pressure roller should be adjusted to adjust the starting direction.
3. If the aluminum foil is biased to the left or right, the adjustable roller seat can be adjusted. If the front and rear deviations are adjustable, the box moves.
4. After the heat seal is punched out, the feeder gate is opened moderately, so that the medicine (tablet capsule, sugar coating) enters the feeding room in an appropriate amount. If there is a small amount of missing grain, it can be manually filled. The first thing to pay attention to when filling the grain: roller pressure roller Rolling hands and hooks break the aluminum foil. In addition, the formed blister is passed to the side of the pressure roller. There is a lack of grain. Do not reluctantly replenish it. Fill the hole. If the drug is brought in, it will affect the synchronization more seriously. When the aluminum foil is sealed, it is light. On the sticky mold, it is necessary to collect the machine.
5, due to increased drug weight, aluminum foil tension and machine temperature gradually change procedures, may cause molding and heat sealing is not synchronized, leading or lagging, first check whether plastic PVC and aluminum foil have a negative separation, and then can be adjusted by fine adjustment mechanism on the machine. The fine adjustment mechanism adjusts the distance or the front and rear adjustment of the cabinet as the mold moves forward and backward. Therefore, it should be placed in the neutral position before starting, so that it can be moved forwards and backwards. It can also be adjusted by moving the front box. After correct movement, the section has to wait for more than ten editions to be correct, so when it is not finished, do not Adjusted to adjust.
6, the heat sealing quality of plastic aluminum foil (bonding even and firm) by temperature or pressure, the relief of the screen plate to see, if there is poor heat sealing, generally suitable temperature, generally suitable temperature, slightly lower pressure, adjust the temperature , Zui adjusts the pressure of the screw.
7. Punching the offset, cutting the layout offset, stopping the manual movement of the box, the mold shift can be adjusted.
Operating procedure of pharmaceutical packaging machine
The medicine packaging machine is mainly used for packaging solid medicines such as capsules, tablets, capsules, suppositories, etc., and adopts the internal heating form, which is a model with lower advanced price at home and abroad. This machine is suitable for: capsules, plain tablets, sugar coatings, capsules, injections, special shapes, etc., as well as medical devices, light foods, electronic components blister sealed packaging.