The electrothermal constant temperature incubator is widely used in many fields. Below we introduce the eight operational points of the electric thermostatic incubator. Adult diapers are disposable urinary incontinence products, one of the adult care products, and a disposable diaper mainly suitable for incontinent adults.
Most products are flaky and shorts type. Use adhesive sheets to connect into a pair of shorts. The adhesive sheet also has the function of adjusting the waist size so as to fit different fat and thin body shapes.
Generally, the structure of diapers is divided into three layers from the inside to the outside. The inner layer is close to the skin and made of non-woven fabric; the middle layer is water-absorbent fluff pulp, added with polymer water-absorbing agent; the outer layer is an impermeable breathable film. Attends Diapers,Free Adult Diapers,Adults Wearing Diapers,Walgreens Adult Diapers Shandong Kangshun Daily Products Co., Ltd , https://www.centurybenifit.com
1. Turn the electric heating constant temperature incubator power switch to “1â€. At this time, the power indicator light is on and there is a digital display on the temperature controller.
2. Temperature setting a. When the required cooking temperature is the same as the set temperature, it is not set without principle, otherwise it needs to be reset. First press the function key "SET" of the electric heating constant temperature incubator to enter the temperature setting state, the SV setting display flashes and flashes, then press the shift key "â—¢" with the plus key "â–³" or minus key "" To end, press the function key "SET" to confirm.
b. If you do not need to set 37~C, the original setting is 26.5~C, first press the function key “SETâ€, then press the shift key “◢â€, move the cursor to the display ten digits, then press “△†To increase the ten digits from "2" to "3", after setting the ten digits, move the cursor to set the digits and quantile numbers in turn, so that the set temperature is displayed as 37~C, press the function key "SET" "Confirm, the temperature setting is over.
3, the upper limit tracking alarm setting The product has been set high 10C before leaving the factory, generally do not set. If you need to reset the function key "SET" for 5 seconds, the meter enters the upper limit tracking alarm. Set the status "ALl" and press the shift key "â—¢" with the plus key "â–³" or the minus key "â–½" operation, and finally press the function key "SET" to confirm. The tracking alarm setting ends.
4. Correction of temperature display value Since the electrothermal constant temperature incubator has been strictly tested before leaving the factory, it is generally not necessary to make corrections. If the environment of the electrothermal constant temperature incubator is not good, the external temperature is too low or too high, which will cause the temperature display value to be in error with the actual temperature inside the box. If it exceeds the technical specifications, it can be corrected. Specific steps: Press the function key “SET†for 5 seconds, the instrument enters the parameter setting cycle state “ALlâ€, continue to press the function key “SETâ€, make “display†SC†correction, then press the shift key, cooperate with the key The temperature correction can be performed by "â–³" or minus key "â–½" operation. Finally, press "SET" to confirm and the temperature display value correction ends.
5. After the setting is completed, the data will be saved for a long time. At this time, the incubator enters a warming state, and the heating indicator lights up. When the temperature in the electrothermal constant temperature incubator is close to the set temperature, the heating indicator lights up and down, repeatedly, and the control enters a constant temperature state.
6. Open the inner and outer doors of the electrothermal constant temperature incubator, put the required cultured items into the incubator, and close the inner and outer doors. If the inner and outer doors open for too long, the temperature inside the box fluctuates somewhat. This is normal.
7. Select the culture time according to your needs. After the culture is finished, turn the power switch to “0â€. If you do not remove the item immediately, please do not open the electric thermostat incubator door.
8. If you have high requirements on temperature control accuracy and fluctuation, you can use PID self-tuning control. When the temperature in the box will reach the set temperature for the first time, press the function key “SET†for 5 seconds, the instrument will enter. Set the cycle status "ALl", continue to press SET "key" to display "ATU", SV display "0000", then press the plus key "△" to make SV display "0001", and finally press function key "SET" to confirm, this When the self-tuning indicator light is on, the temperature controller enters the PID self-tuning control.